View topic - 1915 Dodge Touring

It is currently Thu Dec 14, 2017 3:06 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 8 posts ] 
Author Message
 Post subject: 1915 Dodge Touring
PostPosted: Wed Sep 24, 2014 10:55 am 
Offline

Joined: Tue Sep 23, 2014 5:04 pm
Posts: 9
I am new to the club. I have purchased a 1915 Dodge Touring. I have no rear fenders and would like to know what years and models would interchange. Any information would be greatly appreciated.

Brad


Top
 Profile  
Reply with quote  
 Post subject: Re: 1915 Dodge Touring
PostPosted: Fri Sep 26, 2014 6:51 pm 
Offline

Joined: Sat Feb 11, 2012 5:19 am
Posts: 12
Brad
The fenders that you need in the Master Parts Price List, Fifth Edition, July 1st, 1921 list two different wheel bases 56" and 60" which along with the car number determines which of two style of fenders that go on your car. Just so you know the car number is stamped on a small plate located on the upper toe board in the front compartment of the car, and also stamped on the right side member under the front fender near the front spring rear bracket, also it is stamped near the right end of the frame center cross member which is under the floorboard near the right door.
Where are you located? Good Luck


Top
 Profile  
Reply with quote  
 Post subject: Re: 1915 Dodge Touring
PostPosted: Sat Sep 27, 2014 10:29 am 
Offline

Joined: Tue Sep 23, 2014 5:04 pm
Posts: 9
Dennis,

Thanks for your reply. The serial # is 23009,manufactured in July,1915. The wheelbase from the information I found states 114 inches for the touring. The 56 inches and 60 inches you mentioned ,is that the distance between the wheels on the same axle ?
I'm located in Maine. I will also need a front driver's door ,2 rear doors and a glovebox door. I have 3 doors that were included, they look like they belong to a Dodge as they have a small raised ridge about 3/8 outlining the edges,but the curve on the southeast quadrant of the rear doors is more like a quarter circle.

Brad


Top
 Profile  
Reply with quote  
 Post subject: Re: 1915 Dodge Touring
PostPosted: Sat Sep 27, 2014 3:37 pm 
Offline

Joined: Tue Sep 23, 2014 5:04 pm
Posts: 9
Correction 1915 Dodge touring wheelbase is 110 inches not 114 inches as previously posted.


Top
 Profile  
Reply with quote  
 Post subject: Re: 1915 Dodge Touring
PostPosted: Sun Sep 28, 2014 2:35 am 
Offline

Joined: Sat Feb 11, 2012 5:19 am
Posts: 12
Brad
Woops looks like I read the book wrong it says 56" tread and 60" tread which must mean the distance between the wheels. Sorry about giving you the wrong information. You are right the wheelbase's given in the book are 110" wheelbase for cars below #95489 with a low radiator and 114" for cars above care number 108644 have a high radiator. Cars between 95489 and 10864 may have either a 110" or a 114" wheelbase. I would suggest that you check the Club Region to see if there is someone closer to you who may have a Touring that you could look at or try to find a auto museum to visit. Also go to one or more of the swap meets in your area. You could also provided you have the time go to the swap meet at Hershey, Pennsylvania which is the big one on the East Coast. Good Luck.


Top
 Profile  
Reply with quote  
 Post subject: Re: 1915 Dodge Touring
PostPosted: Sun Sep 28, 2014 10:09 am 
Offline

Joined: Tue Sep 23, 2014 5:04 pm
Posts: 9
Thanks for information.I'm hoping to get to Hershey and view the Dodges on display at the AACA museum and make contact with The Dodge Brothers club members.


Top
 Profile  
Reply with quote  
 Post subject: Re: 1915 Dodge Touring
PostPosted: Sun Sep 28, 2014 6:30 pm 
Offline

Joined: Wed Dec 28, 2011 8:08 pm
Posts: 228
Brad Warner, get me $22 and come to the club dinner/meeting. There are usually about 100 members there, I can think of three 1915 owners for sure.


Top
 Profile  
Reply with quote  
 Post subject: Re: 1915 Dodge Touring
PostPosted: Wed Oct 01, 2014 8:10 pm 
Offline

Joined: Tue Sep 23, 2014 5:04 pm
Posts: 9
Doug,
Thanks for the invite to The Dodge Brothers dinner meeting. Unfortunately, I will not be able to attend Hershey this year. I'll be looking for parts and literature and will hopefully be there in 2015.

Brad


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Bing [Bot] and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group