View unanswered posts | View active topics
|
Page 1 of 1
|
[ 9 posts ] |
|
Author |
Message |
JimLowery
|
Posted: Sun Sep 16, 2018 5:16 pm |
|
Joined: Wed Dec 28, 2016 2:11 pm Posts: 75
|
There is a clutch adjustment procedure for clutch facing wear described on p.47 of the Mechanics' Instruction Manual. Has anybody performed this adjustment? I have a gear grind problem, and had assumed I just have a worn clutch. But a wise friend (a model T guy) suggested, can't you first adjust to max the clutch pedal reach? So that's what inspires this question - I hadn't even thought about it.
|
|
Top |
|
|
Guest
|
Posted: Sun Sep 16, 2018 8:06 pm |
|
|
I have not done that adjustment but do you use neats foot oil on your leather?
|
|
Top |
|
|
Guest
|
Posted: Mon Sep 17, 2018 4:11 pm |
|
|
Jim, I have never done this adjustment. But looking at the parts book it shows a round nut, maybe 2 inches in diameter, at the throwout bearing. It puts more tension on the spring. The nut is split with a screw to clamp it tight on the thread. You have to loosen the screw. Then there are flats formed onto the nuts you can tighten with a drift and hammer. That is IF it needs adjustment. As I asked before do you use neats foot oil on the leather? It is important.
|
|
Top |
|
|
JimLowery
|
Posted: Mon Sep 17, 2018 9:02 pm |
|
Joined: Wed Dec 28, 2016 2:11 pm Posts: 75
|
I am clueless - but yall know that by now. Neats foot oil on the leather - i have research to do. is the clutch plate surface leather? Gone to rookie camp.
|
|
Top |
|
|
JimLowery
|
Posted: Mon Sep 17, 2018 9:24 pm |
|
Joined: Wed Dec 28, 2016 2:11 pm Posts: 75
|
Im still clueless about oiling leather clutch (?) but allow me to revise my initial question. Because I have a gear grind problem, I'd assumed I have a weak springed clutch plate. I don't have a slipping clutch. So the tho't was, maybe the clutch could be adjusted to max the pedal reach - and that's what p.47 Mechanic's Manual seems to address.
|
|
Top |
|
|
Guest
|
Posted: Mon Sep 17, 2018 10:16 pm |
|
|
Jim, I am not going to claim to be an expert. But I have read a few articles on cone clutches. The neats foot oil is to keep the leather soft and so it doesn't grab. From what I read if it slips then you use fullers earth The leather is very thin so I am not sure it should need much adjustment. Go to the Horseless Carriage club site or Skinned Knuckles and do some research. A cone that operates correctly is a very good clutch. And most experts I know say NEVER use kevlar lining. I have worked on cranes that use a cone brake. The taper makes better contact then a disc.
|
|
Top |
|
|
Guest
|
Posted: Wed Sep 19, 2018 8:51 pm |
|
|
Jim, I may be leading you astray. For some reason I thought you were talking about an early car with a cone clutch. In looking at other posts from you you asked a few questions about a '23. Sorry, I have early cars in my head. My '24 had a problem like you describe. I took the cover off the bell housing, in front of the shifter, and made sure all the clutch plates could separate by holding the peddle in and using a screw driver to push them. Then I cleaned the linings with a can of brake clean. Made a big difference. Also make sure your transmission oil is thick enough. Modern 600 is not. I blended in a tube of grease into the thickest steam cylinder oil I could buy. I found it at a place that supplies Strasburg RR that has steam locomotives. Again, sorry for MY confusion.
|
|
Top |
|
|
JimLowery
|
Posted: Wed Sep 19, 2018 11:43 pm |
|
Joined: Wed Dec 28, 2016 2:11 pm Posts: 75
|
<chuckle> Doug I was waiting for you to catch up! -ha Yes my '23 has single plate clutch, not a cone clutch. Agree, a cleaning would be in order. The Mechanics Manual procedure p.47 addresses what I'd hope to gain tho'. Doesn't seem very easy -sounds like a winter project. I did use 600wt in my gearbox. I drained it first of course. Capacity 5 pints per Book O' Info.
|
|
Top |
|
|
Guest
|
Posted: Thu Sep 20, 2018 8:38 am |
|
|
I may not be a good guesser at what year you have, but I do know a '23 doesn't have a single disc clutch.
|
|
Top |
|
|
|
Page 1 of 1
|
[ 9 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 68 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|